
SPECIFICATION

DESCRIPTION
SNCP series inks is, essentially evaporation-drying ink, screen inks for on PC, ABS, ACRYLIC and several kinds of plastics, soft or hard
plastics. It has excellent adhesion, chemical resistance and has lightfast properties. This inks contain specified color that Hologram inks, Glitter ink, Pearl inks.

APPLICATION SUGGESTIONS
SNCP series is formulated low odor solvent and good stability on the screen, A screen mesh size of 250 mesh/inch
plain wave, monofilament polyester mesh will be provide best results and sharp polyurethane squeegee of approximately 75 – 85
durometer 60/90 recommended for optimum results. Inks are supplied at print ready viscosity for most applic
ations. However can be add 15 ~ 20% of reducer if need viscosity control.

WASH UP
Screen may be cleaned with Cyclohexanon, Xylene or many commercial screen washes. We recommended JD-100 Wash up solution for cleanings and clean immediately after printing.

HEALTH & SAFETY
As with this inks, gloves and safety device should be used when handling the products. For more complete information do you need, refer to the Material Safety Data Sheet before use.

STORAGE & HANDLING
The product requires stirring prior to use. The shelf – life is good when stored away from heat and protected from UV light exposure. The material is combustible and should not be used near open flame. Store below 32°C. Best when used within 6months of product Lot No. date on label. Under different conditions, particular higher storage temperatures, the shelf life is reduced.

MONOPIGMENTED COLORS
SNCP 111 |
G/S Yellow |
SNCP 115
| Golden Yellow |
SNCP 119 |
Orange |
SNCP 180
| Blue shade Red |
SNCP 181 |
Cerise |
SNCP 182
| Pink/Rhodamine Red |
SNCP 183 |
Warm Red |
SNCP 149
| Green |
SNCP 155 |
Reflex Blue |
SNCP 159
| Blue |
SNCP 185 |
Violet |
| |

PANTONE FLUORECENT COLORS
SNCP 801 |
Blue |
SNCP 802 |
Green |
SNCP 803 |
Yellow |
SNCP 804 |
Orange |
SNCP 805 |
Red |
SNCP 806 |
Pink |
SNCP 807 |
Magenta |

PANTONE METALLIC COLORS
SNCP 871 |
Rich Gold |
SNCP 876 |
Pale Gold |
SNCP 877 |
Silver |
▶ There can be several metallic color when mixing together from above standard
base color with monopigmented color. Select mesh with opening
large enough to transfer the metallic pigments of choice. Normally a mesh count 305 mesh/inch or lower is required will reduce shelf life of mixtures.

BLACK & WHITE
SNCP 585 |
White |
SNCP 584 |
High Opaque White |
SNCP 582 |
Black |

SWOP PROCESS COLORS
SNCP 131 |
H.T Yellow |
SNCP 171
| H.T Black |
SNCP 140 |
H.T Magenta |
SNCP 139
| H.T Base |
SNCP 135 |
H.T Cyan |
| |

MODIFIER & OTHER PRODUCTS
SNCP 101 |
OP Varnish |
SNCP 199
| Mixing Clear |
SNCP –CA |
Cure accelerator |
SNCP – VM
| Viscosity Modifier |
SNCP – M2 |
Matt Clear |
| |

DISCLAIMER
All information on this data sheet is based on JESCO laboratory test and experience in print press. Procedures and directions for use of JESCO products must be considered as
recommendations only, with no warranties expressed or implied. The printer solely responsible for determining suitability of any JESCO product for the particular application.